Silicone Compression Set: Why Seals Relax and How to Specify Durability

HOME >> BLOG

Silicone Compression Set: Why Seals Relax and How to Specify Durability

Time:2026-11-12
Read:7

Compression set is the difference between a silicone gasket that still seals in its second year and one that leaves a permanent flat spot in month three. The practical conclusion for buyers: for any part that must hold a seal or keep contact force under sustained load, put a compression-set limit and its test conditions into the specification. A number without conditions is marketing, not engineering. As a reference point, a well-formulated, correctly post-cured silicone compound typically recovers 80–90% of its deflection under moderate test conditions; the remaining 10–20% is what your design has to absorb.

What compression set actually measures

Compression set (CS) is the percentage of an applied squeeze that a rubber part fails to recover. The standard test (ASTM D395 Method B, or ISO 815 Method A) compresses a specimen to a fixed deflection — commonly 25% — holds it in an oven for a defined time and temperature, releases it, and measures the recovered thickness after a rest period. The set value is the lost portion of the original deflection, expressed as a percentage. Lower is better.

Two consequences follow. First, the number is meaningless without its conditions: 20% after 22 hours at 70 °C and 20% after 70 hours at 200 °C are entirely different levels of performance. Second, CS is a material-and-process property, not a part property — but part geometry decides how much of it the product can tolerate, which is why the specification needs both.

What drives compression set

  • Temperature. The dominant variable. Every additional 25–30 °C of service temperature roughly doubles the set measured over the same duration, because heat accelerates the relaxation of the crosslinked network.
  • Time under load. Set grows with logarithmic time — a gasket squeezed for a year behaves like a specimen aged far longer than a 22-hour test. Long-duration tests (70 h, 168 h, 1,000 h) exist for exactly this reason.
  • Compound quality and post-cure. Under-cured material and excessive plasticiser or processing oil relax much faster. A proper post-cure bake measurably improves CS on peroxide-cured compounds.
  • Hardness and geometry. Softer compounds (Shore A 20–30) generally show higher set than firmer ones (50–70). Thin sections with high percentage squeeze also see more relative relaxation.

What the numbers typically look like

The ranges below are industry-typical values for general-purpose and premium silicone compounds under 25% constant deflection. They indicate order of magnitude, not a guarantee — individual formulations vary.

Test conditionGood compound, typical CSWhat it means in service
22 h at 70 °C< 15%Room-temperature and mild service; consumer lids, general covers
22 h at 100 °C15–25%Dishwasher cycles, hot-fill containers, under-hood-adjacent parts
22 h at 200 °C30–50%Oven-adjacent service; only platinum grades with full post-cure stay usable
70 h at 150 °C30–40%Long-duration elevated service; seals intended for continuous heat
1,000 h at 150 °C40–60%Automotive and appliance seals; design must tolerate half the squeeze being lost

Where it matters most by product category

ProductWhy compression set mattersPriority
Silicone travel bottle gasketsCap seal held squeezed for weeks between refillsHigh
Collapsible container lid sealsSeal must survive repeated lid compression and dishwasher heatHigh
Bakeware and oven-tray rimsRepeated 200 °C exposure; set shows as warped rimsHigh
Car interior pads and cup-holder matsStatic load, summer cabin temperatures above 70 °CMedium
Phone cases and decorative coversNo sealing function; set is cosmetically irrelevantLow

How to write it into the specification

  1. Method and conditions: "ASTM D395 Method B, 25% deflection, 22 h at 100 °C" — or ISO 815 Method A if your market prefers it. Never accept a bare percentage.
  2. Limit: for example "≤ 25% set" at the chosen condition. Tighter limits cost money; ask for the compound's actual test report first.
  3. Specimen state: post-cured as production parts will be, and tested on the coloured production compound, not natural rubber.
  4. Hardness tolerance: ±5 Shore A around the target, because hardness drift usually signals compound changes that also affect set.
  5. Change control: any compound or cure-system change requires a new CS report before shipment.

Design allowances that make the number survivable

Even a good compound loses some squeeze, so seal grooves should be sized for 20–30% squeeze on O-ring style seals with 10–15% headroom for set, and lid seals should preload the gasket enough that a 20% loss still leaves positive contact force. Where the product cannot tolerate any set, consider a mechanical clamping feature instead of relying on rubber memory. Discussing groove dimensions at quotation stage is cheaper than discovering them in a failed drop-test or leak-test report.

FAQ

Is lower hardness always worse for compression set?

Generally yes, but not catastrophically. Soft food-grade compounds around Shore A 25–40 show somewhat higher set than 50–60 Shore grades, and a well-cured soft compound still outperforms a badly cured hard one. Match hardness to the sealing requirement first, then optimise the compound.

Can compression set be tested on finished parts instead of standard specimens?

Standard tests use moulded plaques or O-rings for comparability. However, a simplified functional check on finished parts — measuring lid-seal thickness recovery after an oven cycle — is a useful goods-in screening step. Use it to compare batches, not to certify the material.

Why did the supplier quote 10% and the shipment test at 30%?

Usually a difference in test conditions, an un-post-cured sample, or a compound change between sample approval and mass production. This is why the written specification must fix the method, temperature, duration and post-cure state.

Does compression set matter for products with no sealing function?

Rarely. For mats, cases and decorative parts, permanent indentation under static load is a cosmetic issue at most. Spending money on premium low-set compounds there is money better spent on tear strength or surface quality.

Next step

If your product includes seals, gaskets or lid closures, send us the groove or lid drawing and the service temperature range, and we will recommend a compound and set limit that matches the real duty cycle rather than the harshest possible test. See our custom silicone OEM and ODM service for the specification process, or browse silicone kitchen products and silicone car accessories where these parameters apply daily.

Related products