Silicone Compression Molding Defects: Flash, Bubbles, Tearing and How to Fix Them

HOME >> BLOG

Silicone Compression Molding Defects: Flash, Bubbles, Tearing and How to Fix Them

Time:2026-11-09
Read:20

When a silicone shipment fails inspection, the defect is rarely a mystery to the factory — it is a symptom of a process shortcut taken earlier that day. Buyers who understand the six common compression molding defects can tell the difference between a one-off process excursion and a factory that will keep shipping the same problem every month.

The six defects that account for most rejects

DefectAppearanceUsual root causeCorrect fix
FlashThin web of material at the parting lineWorn tool, low clamp tonnage, over-chargeTool refurbishment, charge control — not more hand trimming
Bubbles / voidsHoles or hollows inside thick sectionsAir entrapment, insufficient venting, cure too fastAdd vents, vacuum assist, revised cure curve
Short shotIncomplete fill, rounded edgesUnder-charge, cold mould, poor flow pathCharge and mould temperature correction
Tearing on demouldSplits at thin or sharp featuresSharp internal corners, over-cure, rough cavityDesign radius added, demould technique, tool polish
Surface contaminationShiny spots, embedded particlesDirty cavity, release agent misuseCleaning schedule, controlled release agent dosing
Colour variationBatch-to-batch shade driftPigment weighing error, mixed masterbatch lotsWeighing discipline, lot control, master sample sign-off

Notice the pattern: five of the six fixes are process or tooling actions, and only one can be solved by sorting harder at final inspection. A factory whose first answer to a defect report is "we will inspect more carefully" has not found the root cause.

Flash: the defect that looks cosmetic and is not

Flash — the thin skin of silicone that squeezes out at the parting line — is normal in compression moulding in small amounts, and every factory trims it. The commercial question is how much there is and how it is removed. A thin, consistent flash line trimmed with a fixture leaves a clean, repeatable edge. A heavy, irregular flash line trimmed by hand with scissors leaves edges that vary from piece to piece, and that variation shows up in your customer returns.

When flash increases suddenly between batches, the likely causes are a worn parting line on the tool, a clamp pressure that was reduced to shorten the cycle, or an over-charged cavity. Ask the factory which of the three it was. A capable supplier can answer from the batch record; a supplier guessing will change something arbitrary and the flash will return.

Bubbles and voids: a symptom of curing too fast

Silicone cures from the outside in. If the mould temperature is high relative to the part thickness, the outer skin sets while the core still holds air and volatiles, and the trapped gas forms voids. The fixes, in order of preference:

  • Redesign the cure curve — a lower starting temperature with a longer ramp lets the core degas before the skin sets.
  • Add vacuum assist — vacuum during mould closing removes most entrapped air before cure begins.
  • Add or enlarge vents — the cheapest fix, and often the only one needed on thick bosses.
  • Rethink the geometry — a 15 mm solid boss will always be harder to cure void-free than a cored or thinner version.

Bubbles in a transparent or translucent part are visible instantly; in an opaque part they hide until a tear test or a section cut reveals them. This is why sampling on opaque parts should include at least one destructive check on a thick section.

Tearing at demould: usually a drawing problem, not an operator problem

Silicone is strong in tension but weak against stress concentrated at a sharp corner. If parts tear consistently at the same feature — an internal corner, a thin rib root, a deep undercut — the geometry is the cause and the operator is only the messenger. The durable fix is a radius on the drawing and a tool modification. Some tearing also appears when parts are over-cured: fully crosslinked silicone loses elongation and snaps instead of stretching during extraction. Both causes are fixable, but only after the factory admits which one applies.

Short shots and colour drift: the batch-record defects

Short shots — cavities that did not fill completely — and batch-to-batch colour drift are the two defects that separate factories with real process documentation from factories with good intentions. Both defects are traceable: a short shot points to charge weight, mould temperature or press settings at a specific time; colour drift points to pigment weighing or a masterbatch lot change. Ask to see the batch record for the affected production date. If no record exists, expect the same defect again, because nobody can prevent what nobody recorded.

Agreeing the acceptance standard before production

None of this works if "acceptable" is defined at the inspection table instead of before tooling. The practical approach is a defect sheet agreed at sample approval: for each cosmetic zone of the part, state the maximum flash width, the permissible bubble count and size, and the colour tolerance versus the master sample — often expressed as a delta-E limit or simply a signed physical reference. Written standards convert a dispute into a measurement. Without them, every inspection becomes a negotiation, and negotiations after production has been paid for rarely end in the buyer's favour.

FAQ

Can flash-free silicone parts be moulded?

Near-zero flash is achievable with high-precision tooling and tight process control, especially on LSR injection presses, but on conventional compression tooling a small flash line is normal. Specify the maximum acceptable flash width rather than "no flash", which no compression shop can honestly promise.

Should we reject a batch with a few bubbles in opaque parts?

Depends on location and function. Bubbles in a non-critical cosmetic zone of an opaque mat may be acceptable within an agreed AQL; bubbles in a sealing surface or a structural boss are a functional failure. Define this in the defect sheet before the order, not after the container arrives.

How do we know whether the factory fixed the root cause or just sorted the batch?

Look for a process change, not an inspection change: a repaired tool, a new cure curve, a vent addition, a weighing procedure. Ask for a short written 8D or corrective-action summary — a competent factory produces one within a few days, and its content tells you immediately whether the cause was understood.

Next step

If a current or past silicone programme keeps failing on the same defect, send us the part drawing, photos and the inspection report. Our engineering team reviews the failure mode against the tooling and process and tells you what should have been changed. You can review the scope of our custom silicone OEM and ODM service or browse the full product range we manufacture in-house.

Related products